5*5 Mesh Wire Mesh Shuttleless Loom Weaving Machine For Filter Stainless Steel Wire Mesh
The Appllication of the Wire Mesh Weaving Machine
Stainless wire mesh
KINGGANG wire mesh
Mosquite Wire Mesh,
Filter wire mesh
Cobber wire mesh
Square Wire mesh filter
The weaving way including plain weave, tilted weave, bead weave and tapered contrast microgroove
Main features
1. High adaptability to metal wire: Apply to imported and domestic metal wires
2. Large adjusting range: Weave 14-400 mesh square hole mesh or 2600 mesh special mesh with various lines, such as plain weave, twilled weave, satin weave, taper contrast thick mesh weaving, superior to other models
3. It adopts shuttleless straight line weft insertion weaving and mechanical automatic let-off and take-up, has small opening amount and smooth wire side, can weave microgroove mesh without bright spot or bright channel and produce high-grade screen mesh, and conforms to national standard.
4. Low center of gravity, good stability, low noise, less energy consumption, high efficiency
5. Reasonable design, simple structure, convenient operation, easy regulation and repair
The technical parameters are shown in the Table below.
| TYPE 型号 | ZWJ-1300D | ZWJ-1600D | ZWJ-2100D |
| MESH SIZE 网面密度 | 20-140mesh/inch | 20-140mesh/inch | 20-140mesh/inch |
| WIRE DIAMETER 丝径范围 | 0.10-0.35mm | 0.10-0.35mm | 0.10-0.35mm |
| BEATING-UP FREQUENCY 打纬次数 | 70 r/min | 70 r/min | 70 r/min |
| MESH WIDTH 织网宽度 | 1300mm | 1600mm | 2100mm |
| MOTOR POWER 电机功率 | 2.2kw | 2.2kw | 2.2kw |
| OVERALL SIZE 外形尺寸(长×宽×高) | 3.0m*2.8m*1.4m | 3.0m*3.1m*1.4m | 3.0m*3.6m*1.4m |
Operation
- The weaving machine can be started up and stopped at any running position.
- It has the function of automatic stop and red/green light indication at weft or warp broken.
- At a fault of weft broken or warp broken, the weaving machine will be automatically stopped and the red/green light will give an indication. The weaving machine can be brought back into normal operation after the fault is removed, the STOP button is pressed down, and the indicator is turned off. If the indicator does not turn off when the STOP button is pressed down, and the weaving machine can not be brought back into normal operation even by pressing down the FORWARD button, it means the fault hasn't been removed yet.
- When necessary, the weaving machine can be stopped at any running position by pressing down the STOP button.
- The weaving machine will be brought into reverse running by pressing down the REVERSE button. Usually reverse running is required at any weft broken, but it is recommended not using this function frequently otherwise the rapier will break off the warp line or the motor will be damaged because of overheat.
Machine picture
The weaving machine shall be transported and handled by a hoisting apparatus.
The antirust oil on each part shall be swept away before trial operation.
The worm gear box shall be filled with oil, and the oil shall be full over the gears, and each lubricating cup, oil hole, gear pair, worm gear pair, sliding pair and other lubricating part shall be sufficiently oiled.
The motor and the housing shall be correctly earthed.
After the weaving machine is connected to the power supply, make the rotor rotate in no load to check whether it rotates in a correct direction.
Before trial operation, firstly turn the knob to the MANUAL stage, and then manually turn the handwheel at the left of the crankshaft at least for two circles when two bolts of heald are used and four circles when four bolts of heald are used to check whether there is any jamming or any other irregularity, and finally turn the knob to the AUTOMATIC stage before pressing a button.
Product Tags:
|
|
5*5 Mesh Wire Mesh Manufacturing Machine , Shuttleless Loom Weaving Machine Images
|
